Search results for '70mm plate'

Mishimoto 13+ Ford Focus ST Thermostatic Oil Cooler Kit Fits all Focus ST (all years) Turbocharged, high stress 4 cylinder engines like the 2.0L EcoBoost engine in the Focus ST can overheat their oil very quickly within a few laps on the track or aggressive street driving. Even with the stock liquid-liquid head exchanger, the engine can still run very hot and run the risk of overheating the engine's coolant as well. Aggressive tunes and some track miles can significantly overheat your oil wear down your engine. Leave it to Mishimoto to come up with an oil cooling solution to your Focus ST! The Mishimoto engineers started with a large 19-row oil cooler and mounted it in the front of the vehicle where it receives the most airflow. The oil cooler was mounted on the passenger side as to not interfere with some aftermarket air intake systems. Application specific braided stainless steel lines transfer the oil from the cooler to the engine and feature -10AN fittings for an easy installation. Mishimoto engineers saw consistent temperature decreases of over 30 F (16.7 C) using our non-thermostatic sandwich plate. Proving that this oil cooler kit can withstand the stresses of the most extreme applications. This oil cooler kit is available with either a Stealth Black or Sleek Silver cooler and your choice of the Mishimoto Oil Sandwich Plate or the Mishimoto Thermostatic Oil Sandwich Plate. As with all our products, this kit includes the Mishimoto Lifetime Warranty. Focus ST Oil Cooler - Benefits: https://www.youtube.com/watch?v=bngb10smBvs Install Instructions: https://www.youtube.com/watch?v=5R5wBmrT8DM&feature=youtu.be Learn More

Ford Stage 1 Drivetrain Package (Exterior) Focus ST 2013-2018, Focus RS 2016-2018 The Stage 1 Drivetrain Package Includes: Adjustable Shift Plate, Shifter Cable Bracket Bushings, Shifter Cable Bushings. Ford Adjustable Shift Plate Ford Shifter Cable Bracket Bushings Ford Shift Cable Bushings Learn More

Nissan Juke FWD Midpipe Application: Nissan Juke FWD Front Wheel Drive - CVT and Manual SV, S and RS Models Years: 2011 to 2017 Material: Stainless Steel / Polished Size: 70mm Defouler included in the midpipe for no check engine luight 2JR introduces their 70mm Full 304 Stainless Steel Midpipe for the FWD Nissan Juke. Gains over 20wtq and 15whp without a tune!! Made from 4mm thick 304 Stainless Steel for long life, corrosion resistance and strength in the harshest environment. Direct bolt on with no modification required. And no check engine light because an 02 Spacer is built in to the midpipe! Removes the second cat in the midpipe - the primary cat remains in the downpipe. No smell, no noise - and over 20wtq!! Learn More

WE KNOW IT'S A LOT - BUT PLEASE READ BEFORE ORDERING! Template for the cowl cutout - use only as a reference https://1drv.ms/u/s!AjQkUN52fS1SkYsxogJlFVCW9jLMrw Check out the full install of the 2J Racing cowl induction intake for the Focus St here: https://youtu.be/MtipNgHJUX0 Check out the complete unboxing of the NEW 2J Racing cowl induction intake for the Focus ST and RS here: https://youtu.be/zhqUlagPoRI Check out the Comparison between the NEW 2J Racing cowl induction intake and my old depo intake here: https://youtu.be/GoTbfZnQ3EI 2JR introduces the world's first and only cowl induction intake for your Focus ST. Most intakes place the air filter behind the stock fans to pull heated air directly into the engine (after being heated again by the compression of the turbo). 2JR places the filter inside the cowl, where it only receives ambient cold air from beneath the windshield - in a very high pressure area (another benefit). NOTE - this intake IS LOUD. To us tho, it sounds amazing. Please refer to the "production photos" listed to the left of the final version of the intake. You will lose your sound symposer - you do not need a block off plate (you can just remove the tube). The 2JR Cowl intake does include the provision for the EVAP hardline. Its completely plug and play - the OEM hardline clips in to our machined fitting - we have an extension hose that connects to the cowl intake. Same for the IAT sensor - instead of the silly grommet ours is a machined fitting the sensor rotates into - just like stock. So it'll never come lose or leak. - Install time - 2 hours. A tune is not required. - In testing we saw ambient or just a deg or two below ambient during cruising and slight increases under heavy load. - To install you will need to cut the lower plastic housing under the cowl (very easy) and the upper cowl vent panel (we will provide a template for the vent panel) - you will also need to extend your IAT wires (2 of them) by 36" or purchase the optional JMS IAT Extension. All other hoses, clamps and K&N Air Filter are included in the kit. - Made in the USA for perfect fitment and quality. NOTE: The intake filter sits suspended in the cowl (not resting on the floor). The was done to prevent any water from being pulled in the intake that may build up on the cowl floor. We do recommend the optional KN filter sock to help keep the filter extra dry - as the piping turns down very close the the plastic upper cowl seal at the windshield. For added security you could trim the upper cowl to act as a bit of flashing to help offset any water intrusion. In testing, we didn't incur any issues during heavy rains - but you should always maintain the highest precaution against this occurring in your neck of the woods. FINAL NOTE: JMS made for us the IAT extension harness. If you dont want to add 36" to your stock IAT harness (2 or 4 wires need to be extended) add this JMS harness in the options. Makes for a painless install. We also recommend the KN Dry filter Sock to help keep it dry. Learn More

McLeod Tuner Series Street Tuner Clutch Altima 2002-06 2.5L Sentra 2002-06 2.5L Spec V STREET POWER- The Street Power clutch kit is the newest offering in the Supremacy Line for the Sport Compact and European Markets, it's the perfect choice for street/track applications. We recommend it for cars up to 40-50%% more power(depending on part number) perfect for street cars with moderate bolt on's. Included is a high quality matched pressure plate, high torque ceramic 6 puck disc for smooth and even engagement. Our kits are complete, they come with pilot tool and throw out bearing (where applicable). If you are looking for a clutch that's a great replacement from your stock set up, the McLeod Street Power is your best option. Supremacy by McLeod Racing. Learn More

OEM Nissan Clutch Kit (Juke / B17) Application: Fits All Models Nissan Juke with MR16DDT (1.6L) Manual Fits All Models Nissan B17 Sentra SR / Nismo MR16DDT (1.6L) Manual OEM Part Numbers: 12310-3YV0A: $1,084.77 Flywheel 30100-1KCOA: $214.86 Disk 30210-1KC0C: $234.85 Pressure Plate OEM New Nissan Complete Clutch Kit. Includes Flywheel, Disk, Pressure Plate and Pressure Plate Bolts. Optional - OEM LUK Concentric Slave Unit Removed from New Nismo RS Engines. Learn More

QR25 (B15) Pressure Plate Bolt/Washer Set OEM Pressure Plate Bolts/Washers for the QR25 OEM and aftermarket clutch kits. It is recommended you replace your OEM pressure plate bolts when doing a clutch replacement. TQ Spec is 24ft/lbs Learn More

Remark 2019+ Toyota Corolla Hatchback Cat-Back Remark Exhaust w/Stainless Polished Tip PRODUCT FEATURES : - 2.5inch, 16 gauge T304 stainless steel, mandrel bent pipe - Dual center-out exhaust system - Slant cut tips for sporty style - OEM factory style exhaust hanger rod construction - High quality hand welding - Gaskets and bolts are included - Direct bolt-on easy to install - Remark license plate frame included Learn More

E210 Stainless Rear Bash Bar 2JR Stainless Steel Bash Bars are the ultimate statement for your Sedan E210 Corolla. Tig welded to perfection for the perfect look and performance. 5" Jack Points, 3/16 mild steel mounting plates. No modifications required. The black section of the OEM bumper easily removes without any cutting or trimming. Stainless Steel Tubing 3/16 Thick Mild Steel Plates Threaded Inserts for License Plate attachment points 5" Jack Point Fits only 2019+ Corollas Learn More