Search results for '2007 sentra'
-
Nissan 55mm Full Race Wheel Studs - fits all models
Regular Price: $5.25
Special Price $3.68
We were asked to make these for the GTRs (we make their hubcentric wheel spacers) and we are offering these for the Sentras as well. This is a true racing wheel stud with rounded ends for wheel changes without damaging the threads. It also allows you to set your lug nuts on the studs for quick install with an impact gun. All the specs were designed with the GTR in mind, thread length, strength, material and longevity. These aren't black, zinc coated studs that quickly rust. These studs will never rust and can handle 25mm of increased track width per side. 55mm, Forged Chromoly SCM435. Also available in 82mm SOLD AS EACH $59 for pack of 16. Learn More -
Mail In UpRev Reflash Service - Send in your ECU
Regular Price: $479.00
Special Price $399.00
Whether you are normally aspirated with bolt ons or turbocharged, with over 300 ROM tunes in our library we can make your Nissan run faster and make more power. We have logged 1000+ dyno pulls with different mod combinations. Send your ECU to 2JR, and in 24hrs (1 business day) we will ship back to you a Uprev/2JR tuned ECU. Ship to: 2J-Racing 1685 Redi Rd Cumming GA 30040 Parameters that we will tune include: Idle RPM Speed Limiter Electronic Throttle Control to achieve Wide Open Throttle at all speeds. Rev Limiter DTC disable AFR Targets Fuel Compensation (for NA or Turbo cars) Ignition Timing Advance Cam Phasing Learn More -
Nissan 82mm Full Race Wheel Studs (fits all models)
Regular Price: $5.99
Special Price $4.25
We were asked to make these for the GTRs (we make their hubcentric wheel spacers) and we are offering these for the Sentras as well. This is a true racing wheel stud with rounded ends for wheel changes without damaging the threads. It also allows you to set your lug nuts on the studs for quick install with an impact gun. All the specs were designed with the GTR in mind, thread length, strength, material and longevity. These aren't black, zinc coated studs that quickly rust. These studs will never rust and can handle 40mm of increased track width. There hasnt been a 12x1.25 with the correct knurl for a Nissan until now. 82mm, Forged Chromoly SCM435. SOLD AS EACH Learn More -
APEXI SAFC 2 II S-AFC Super Air Flow Converter
Regular Price: $429.98
Special Price $399.98
The SUPER AFC II is a fuel adjustment controller in which the airflow sensor signal or the pressure sensor signal can be modified in a 12 point RPM range by 1% increments to increase/decrease fuel in a range of ＋50% to －50%. The RPM to be corrected can be optionally set in 200 RPM increments, and corrections can be made according to throttle opening amounts. In a turbo equipped vehicle with a hot wire type airflow meter, this controller provides a preventive function for engine stall due to blow-back during throttle return. The controller, which includes a knocking meter, allows the monitoring of knock levels check keeping the engine under its optimum condition at all times. (Vehicle must have a factory knock sensor Step by Step install http://www.allsentra.com/viewtopic.php?t=10&fbclid=IwAR2rxswRey3oDAO1HcVkUrB4cKpcMldgkJ0wV4LTQ5GA7wdpbzFTpSydRY8 Instruction Manual https://apexi-usa.com/manuals/electronics/safc2_manual.pdf Wiring https://apexi-usa.com/manuals/electronics/safc2_wiring.pdf Learn More -
B15 Rear Hub Assembly / Bearing Set
Regular Price: $74.99
Special Price $64.79
Pair of rear hubs for the B15 - fits both the 1.8L and 2.5L B15 Sentras (2002-2006). Comes with OEM studs installed. If you want 55 or 82mm studs installed, order those separately and we'll install them for you. 2 Hubs are included Learn More -
B15 Timken Front Bearing Set (Pair)
Regular Price: $96.24
Special Price $92.14
Pair of sealed Japan Timkin Front Wheel Bearings for the B15 - fits both the 1.8L and 2.5L B15 Sentras (2002-2006). 2 Bearings are included Learn More -
PRE ORDER B15 V2 Long Runner Medusa UEL Header
Through continuous testing 2JR has improved the already dominate Medusa header with performance upgrades. Port changes to Oval Head Port Matched Flanges for a perfect seal - Longer runners by 4" over the V1 Medusa produce a higher mid-high rpm HP performance. And stepped runner design from 1.7" to 1.9" from the Spyder header help improve scavenging and broaden the torque curve. The V2 Medusa is UEL (unequal length) and provides a "boxer-like" rumble at idle and under throttle. Comes with Billet Aluminum Alternator Clearance Bracket. You will need one slim fan (included) to run this header because of its size and runner design. It will bolt to the OEM midpipe or the 2JR 2.5 or 3" midpipe. You can remove the fan and ACB option and save an additional $74! Make sure you have these parts already. For a quick install - select the 2JR Plug and Play Fan Wire kit To install the fan - the factory clip has 4 wires, the top two are position (looking at where the clip is) and the bottom two are neg. Connect the blue fan wire to the top two + pos wires and the black 2J fan wire to the bottom two - wires. Fits all 02-06 Sentras and Altimas - qr25de only. Learn More -
B15 12.2" Wilwood 4 Piston Big Brake Kit (02-06 Sentra)
Regular Price: $1,079.98
Special Price $949.99
One of the best brake upgrades for the B15, and helped us to win a National Championship. Complete with Forged Billet Dynalite Calipers, 12.19" diameter rotors, and high performance Wilwood brake pads generate big brake stopping power to compliment wheel, tire, and suspension upgrades on your B15 Saves over 15lbs over the stock brakes - of unsprung weight!. INCLUDES STAINLESS FRONT LINES - AT NO CHARGE
These Big Brake kits require at least 16" diameter wheels.
Kit includes parts for both front wheels:
.810" Thick x 12.19" O.D. Two Piece Rotors
Forged Dynalite Calipers - Black or Red
2JR Caliper Mounting Brackets and all hardware with stainless brake lines
BP-20 Wilwood Smart Compound Brake Pads
* All Hardware necessary to install the complete braking system on both front wheels.
For 02-03 stock wheels you will need 2JR 15mm spacers and 55mm studs Learn More -
QR25 JWT Beehive Spring
$244.48QR25DE JWT BEEHIVE SPRING FOR USE WITH JWT COMPETITION CAMSHAFTS TO .600" LIFT. MUST USE RETAINER ARETN-BHIVE ON EARLY ENGINES. 35.96mm INSTALLED HEIGHT, USE ORIGINAL SPRING BASE SHIMS. Complete set FITS: ALTIMA 2002+, SENTRA 2.5L ENGINES: QR25DE Learn More -
QR25 JWT CAMSHAFT SET C1 BILLET CAMS
Regular Price: $699.98
Special Price $649.98
Ultimate in cams for your QR motor. Go big with the C1s.CAMSHAFT SET QR25DE C1 BILLET CAMS, BETTER THAN THE JWT S1 CAMS ABOVE 3500 RPM WHEN USED WITH 2J RACING LONG TUBE HEADER, 3" COLLECTOR AND LOW RESTRICTION EXHAUST SYSTEM. THERE IS ANOTHER 10-15 HP POTENTIAL BEYOND THE JWT S1 CAMS FOR A COMPETITION ENGINE. C1 IS A LARGE PROFILE
FITS: ALTIMA 2002+, SENTRA 2.5L B15 and B16,
ENGINES: QR25DE,
Suggested to use Brian Crower Valve Springs Install Instructions http://www.jimwolftechnology.com/wolfpdf/CAM_ASER2-QRNC1_HEAD_CLEARANCING_INST.pdf http://www.jimwolftechnology.com/wolfpdf/CAMSHAFT_INSTALL_QR25DE_INSTRUCTIONS.pdf Learn More -
QR25 JWT CAMSHAFT SET S1 BILLET CAMS
Regular Price: $699.99
Special Price $649.98
CAMSHAFT SET QR25DE BILLET CAMS. GOOD IDLE AND DRIVABILITY WITH AN 8+HP GAIN. USES STOCKS SPRING AT STOCK REV CUT OR AQR25-SPRNG SPRING SET IF RUNNING TO 7200RPM.
FITS:
S1 Cam - Excellent street cam, good power and idle. Go with the best, JWT Learn More
ALTIMA, SENTRA, ALTIMA 2002+, SENTRA 2.5L,
ENGINES:
QR25DE, -
IN-CHASSIS VALVE SPRING COMPRESSOR fits most VQ, KA, QR, & VK engines
$92.99IN-CHASSIS VALVE SPRING COMPRESSOR fits most VQ, KA, QR, & VK engines Learn More -
JWT QR25 HEAVY DUTY CLUTCH SET
$326.42QR25 HEAVY DUTY CLUTCH SET WITH 50% HIGHER CLAMPING FORCE THAN STOCK AND A 10M.M. OUTSIDE DIAMETER INCREASE. YOU MUST USE THE JWT ALUMINUM FLYWHEEL WITH THIS CLUTCH. Learn More -
Nissan Sentra Lightweight Racing Pulley 2.5L, QR25DE, Fits Sentra, Altima, Frontier
Regular Price: $129.99
Special Price $99.98
Nets 5whp/5wtq! 2JR introduces a lightweight solid billet 6061 racing pulley that weighs 80% less than the stock pulley (5.1 lbs vs 1lb 2JR), which translates into less rotational mass and quicker revving. All pulleys are built with the factory timing marks and DO NOT require a belt change. This is a simple bolt on for more power in less than 30mins. Fits all 2.5L Sentra B15, Sentra B16, Altima and Frontier
Choose between Red/Blue/Black. Also available with 2JR Powersteering pulley for all 02-06 2.5L QRs. Learn More -
QG18DE (1.8L) B15 Sentra Lightweight Racing Pulley (01-06)
Regular Price: $149.99
Special Price $119.99
FINAL RUN / SMALL BATCH (1.8L) B15 Sentra Lightweight Racing Pulley (01-06) Weighing only 1lb 9oz. 2JR introduces a lightweight solid billet 6061 racing pulley that weighs 82% less than the stock pulley, which translates into less rotational mass and quicker revving. All pulleys are built with the factory timing marks and DO NOT require a belt change. This is a simple bolt on for more power in less than 30mins. Grab yours on the final limited run. IN STOCK Learn More -
2JR Underdrive Lightweight Power Steering Pulley (QR25)
Regular Price: $89.99
Special Price $69.98
2JR releases the lightest power steering pulley ever made for the B15. The underdrive size increases the torque and horsepower output of the QR25 by reducing parasitic drag caused by the belt-driven power steering, but more importantly by reducing the moment of inertia. Excellent steering feel and with a more weighted response in the wheel. No more pump cavitation during extreme cornering. Color:Blue, Black or Red Hard Anodized, 2JR Logo Weighs just 11oz!! Dayco poly rib #5060895 belt REQUIRED. Or similar 89.5" length belt Fits 02-06 Nissan Sentra SE-R & Spec-V (2.5L) 02-06 Nissan Altima 2.5L Does not fit B16s Learn More -
2JR TrueCarbon Top Bin Cover
$114.00Our long awaiting carbon fiber interior and exterior pieces for the sentra (all models) are HERE. Carbon offers high stiffness, high tensile strength, low weight, high chemical resistance, high temperature tolerance and low thermal expansion. Our pieces are combined with a plastic resin to form carbon fiber reinforced plastic which has a very high strength-to-weight ratio, and is extremely rigid and durable. The top bin cover (tbc) and rear trunk center cover (rtcc) are ultra thin and affixed using supplied 3M backing. The gauge cluster panel (gcp) and shifter console panel (scp) are OEM replacement pieces. Get in early during the production run to save your spot and get a 30% savings. EXPECTED LATE 4Q12. Full Carbon Top Bin Cover - 1.5m thick Regular Price: $85 GB Price - $65 Learn More -
2JR TrueCarbon Gauge Cluster - OEM
$235.00Our long awaiting carbon fiber interior and exterior pieces for the sentra (all models) are HERE. Carbon offers high stiffness, high tensile strength, low weight, high chemical resistance, high temperature tolerance and low thermal expansion. Our pieces are combined with a plastic resin to form carbon fiber reinforced plastic which has a very high strength-to-weight ratio, and is extremely rigid and durable. The top bin cover (tbc) and rear trunk center cover (rtcc) are ultra thin and affixed using supplied 3M backing. The gauge cluster panel (gcp) and shifter console panel (scp) are OEM replacement pieces. Get in early during the production run to save your spot and get a 30% savings. EXPECTED LATE 4Q12. Full Carbon Gauge Cluster - OEM replacement Regular Price: $235 GB Price - $170 Learn More -
2JR TrueCarbon Rear Trunk Surround
$290.00Our long awaiting carbon fiber interior and exterior pieces for the sentra (all models) are HERE. Carbon offers high stiffness, high tensile strength, low weight, high chemical resistance, high temperature tolerance and low thermal expansion. Our pieces are combined with a plastic resin to form carbon fiber reinforced plastic which has a very high strength-to-weight ratio, and is extremely rigid and durable. The top bin cover (tbc) and rear trunk center cover (rtcc) are ultra thin and affixed using supplied 3M backing. The gauge cluster panel (gcp) and shifter console panel (scp) are OEM replacement pieces. Get in early during the production run to save your spot and get a 30% savings. EXPECTED LATE 4Q12. Full Carbon Rear Trunk Center Cover - 1.5mm Regular Price: $290 GB Price - $205 Learn More -
2JR Crossmember Delrin Bushings- Wheel Hop Aid (B13/B14/B15)
Regular Price: $59.99
Special Price $39.99
2002-2006 B15 Sentra 2.5L / Replace the old, worn out rubber OEM crossmember bushings with 2 piece delrin bushings from 2JR. Installed between the crossmember and chassis, at all four attachment points. Delrin absorbs some of the motor vibrations for a smoother ride. Zero flex, holds the motor solidly in place. SOLD as a set of 8 pieces, front and rear crossmember locations Can be used on a B13/14 - if you slightly open up the holes on the B13/14 crossmember. Very simple install
In Stock
Learn More