Search results for 'oem kit'
-
(Hatch) Race Side Exit Catback Exhaust
Regular Price: $420.00
Special Price $399.78
(Hatch) Race Side Exit Catback Exhaust Weighs under 10lbs! Designed for track use with hard chassis mount w/isolator and sits tucked up high for extreme low E210s. Options include: - Full Race without a Resonator - 8DB Quieter with Optional Resonator (+$45) Tip Style: - Stainless Oval Single Tip - NASCAR 10" Boom Tube with 2JR Logo (+$95) - Quad (4) 1 3/4" Stainless Tips (+120) Exhaust is full stainless steel for long life. Refer to the attached photo for install tips! Specs: 2.5" 304SS with Flex Race Spec Resonator (optional) Hard Chassis Mount with Rubber Isolator Bolts directly to OEM Midpipe or 2JR Midpipe No cutting or Fab work required Note: You must remove the heat shielding and plastic where the exhaust routes. This easily unbolts from the chassis. Heat Shielding around the gas tank remains. Learn More -
OEM Turbocharger - Nissan Nismo RS (14411-1KC1E)
Regular Price: $987.19
Special Price $689.78
OEM Turbocharger - Nissan Nismo RS (14411-1KC1E) This turbocharger does not include hardware, gaskets, heat shields, or other additional pieces. These must be purchased separately or recycled from your old turbo. Genuine: Nissan OEM SKU: 14411-1KC1E Other Names: Turbo Charger Description: Fits Juke Juke. From 08/2011-2014 and all nismo rs. Condition: New Replaces: 14411-1KC1B, 14411-1KC1C, 14411-1KC1D Sold In Quantity: 1 Learn More -
QR25 (B15) Pressure Plate Bolt/Washer Set
Regular Price: $36.99
Special Price $26.78
QR25 (B15) Pressure Plate Bolt/Washer Set OEM Pressure Plate Bolts/Washers for the QR25 OEM and aftermarket clutch kits. It is recommended you replace your OEM pressure plate bolts when doing a clutch replacement. TQ Spec is 24ft/lbs Learn More -
Seibon Corolla OEM Carbon Fiber Hood
Regular Price: $994.50
Special Price $869.78
Seibon Corolla OEM Carbon Fiber Hood Fits 19+ Models / Hatchback and Sedan OEM Style CF Hood - Hood Pins are Recommended - Ships Truck Freight Direct from Seibon TO CHECK OUT SHIPPING: Shipping is $335 Flat Rate to any of the 48 States. Select the truck freight option below, then $9.89 at checkout. Shipping times are 2-3 weeks for delivery. ONLY SHIPS TO LOWER 48 STATES. NO INTERNATIONAL SHIPPING. Disclaimer: Seibon packs all products carefully to prevent damage during shipping. However, damage may still occur occasionally. Buyer must inspect the packaging and the products carefully upon receiving them, then accept the shipment and notate any damages and irregularities, such as crushed, torn, punctured, or broken parts on both the packaging and the product, on the freight bill or receipt at the driver's presence. Buyer must retain all cartons, packing materials, and damaged products for the carrier's damage inspector to inspect. Do not refuse shipment or return it without approval, because the buyer's right to make a damage claim may be denied. A signed receipt without any notation indemnifies the carrier as well as Seibon from any further damage claims. Discovery of damages after a clear delivery becomes the responsibility of the customer. All damages must be notified to carrier and Seibon within 24 hours. In cases of damage with proper notation on receipt, the carrier will determine whether to pay for repair cost or replacement value of the damaged goods after damage inspection. Replacement value is the amount the buyer paid to the distributor and is not negotiable. All disputes about the settlement amount should be addressed with the carrier. Seibon, under no circumstances, shall be liable for the damaged product or for subsequent settlement of the claim with the carrier. Learn More -
PRE ORDER 3" Resonated Midpipe Corolla GR
Regular Price: $479.98
Special Price $359.78
3" Resonated Midpipe Corolla GR Limited Run of GR Race Resonated 3" Midpipes opens now for the Corolla GR. Made from 304 Stainless Steel and Tig Welded (back-purged) to ensure the highest flow, then paired with a large resonator to reduce rasp and noise. Bolts directly to the OEM Downpipe and designed to fit on the OEM and aftermarket catback exhausts. Increases sound levels by 4-6DB over stock with OEM Catback. Includes HD Front Donut gasket to Downpipe. You will reuse your OEM Spring Bolts for the Fr / Rr of the midpipe as well as the rear OEM Donut gasket. * CNC'd 1/2" Rear Flange for Heavy Use * Race Spec Resonator / Stainless Learn More -
Garrett G30-660 STANDARD ROTATION, 0.82 A/R, T3 Undivided (open), T31 (Narrow) 4 bolt
Regular Price: $2,589.47
Special Price $2,497.78
Garrett® G30-660 standard turbo assembly kit with 3" inlet and 2" outlet compressor housing and 0.82 A/R T3 undivided (open), T31 4 bolt (narrow) outlet turbine housing. Fits on the 2JR Tubular Turbo Manifold. Product Features: New G Series compressor wheel aerodynamics / Fully machined speed sensor and pressure ports / Standard and reverse rotation configurations available / Oil restrictor and water fittings included with purchase / One piece center housing and backplate for increased durability / 4 water jacket ports for customizable installation / Mar-M turbine wheel material rated up to 1050° C | 1922° F Product Specifications: Compressor Wheel Inducer: 54mm / Compressor Wheel Exducer: 67mm / Compressor Wheel Trim: 65 / Compressor Housing A/R: 0.70 / Turbine Wheel Inducer: 60mm / Turbine Wheel Exducer: 55mm / Turbine Wheel Trim: 84 / Includes Oil Feed (1mm) Restrictor Fitting to -4AN / Includes two Coolant Fittings to -6AN Optional Accessories (kit) 4 Bolt "T31" Narrow Outlet Flange (for Downpipe): Product Code:ATP-FLS-084 4 Bolt "T31" Outlet Gasket: Product Code:ATP-GSK-012 Oil drain flange: Product Code: ATP-FLA-010 Oil drain gasket: Product Code: GRT-GSK-008 Oil drain fasteners: Product Code: MIA-FST-034 Boost Pressure Port Fitting: ATP-FTG-198 Learn More -
Toyota / Nissan Spring Bolts (Pair)
Regular Price: $16.45
Special Price $15.80
Toyota / Nissan Spring Bolts (Pair) Application: Toyota E210 / GR Nissan Juke / B17 SR / Nismo Used at the header / downpipe connection (M10x1.25) - fits OEM and 2JR Header (E210/GR) and OEM Nissan Downpipe Learn More -
2JR Dual Vibrant Ultra Quiet / Single Carbon Catback (Hatch)
Regular Price: $989.98
Special Price $949.78
2JR Dual Vibrant Ultra Quiet / Single Carbon Catback (Hatch) Design to fit with the chrome OEM bumper trim removed or rear diffuser Features: Twin Vibrant Ultra Quiet Mufflers Center Resonator 2JR 4.5" Single Carbon Tips Stainless Piping with Flex Section E210 Hatch 2.0L ONLY - fits Manual and CVT Released in limited quantities, a Dual Vibrant Ultra Quiet Catback is now available for your E210 Hatch. No rasp, just deep, clean sound and big performance gains. Stand out from the crowd. Built with only the best parts available - including twin Vibrant Ultra Quiet Mufflers, 2.5" Stainless Steel piping and integrated flex section. Designed to fit your OEM or 2JR Midpipe (inc the 2JR Header). Learn More -
Stage 3 - SR / Nismo Catback + Midpipe + CAI + FMIC
Regular Price: $1,679.98
Special Price $1,498.78
Stage 3 - SR / Nismo Catback + Midpipe + CAI + FMIC Includes: 2JR Carbon Catback 2JR Midpipe w/defouler 2JR Full Cold Air Intake 2JR Full FMIC with Hard Piping Kit Big power gains / no check engine lights / retains the factory front cat / amazing sound without the rasp. Looking for the best sound, performance and quality for your 2017-2019 Nismo Sentra SR and Nismo (1.6L Turbo)? Look no further than our hand-tig welded 2.5" stainless catback with 3.5" Carbon/Blue tip. Includes a long front resonator to remove the rasp and produce that deep, clean sound you've been searching for. It also comes with 3 hard hangers for the tail section, stainless hardware and gaskets for a complete bolt-on system. Remember, the factory turbo exhaust is a mere 49mm - and highly restrictive under boost. Unless your car's potential with 2JR. 2JR Nismo Intake relocates the filter outside of the engine compartment to deliver cool air inlet temperatures. Cooler air carries more oxygen, which translates into a more intense explosion in the combustion chamber to create more horsepower and torque. 2JR Sprint Series FMICs are designed to be used on the street or track with no limitations in performance and to be a complete drop in kit. Kit includes all the hard piping! From the turbo to the throttle body. Complete kit! Features and Benefits: - Direct fit for the 2017-2020 Nissan Sentra B17 Turbo(SR and Nismo models) - 27" Long intercooler design optimized for maximum flow - No modification to front bumper and retains stock fog lights - Maximum cooling efficiency with minimal pressure drop - Max power gains of 19HP and 22 feet per pounds of torque - Drops intercooler outlet temperatures by 38°F - Increases core size by 138% and fin surface area by 42% All the hardware required to complete your installation is likewise included. Learn More -
Spyder Nissan 350Z 03-05 Projector Headlights Xenon DRL
Regular Price: $779.98
Special Price $565.98
Spyder Nissan 350Z 03-05 Projector Headlights Xenon DRL These headlights are designed to improve looks and visibility for your vehicle. They are made by OEM approved and ISO certified manufacturers. They are made with OEM standard quality and are designed for stock lights direct replacement. Learn More -
Hard Line Upgrade Kit
Regular Price: $298.98
Special Price $279.77
Hard Line Upgrade Kit For the 2JR Air/Water turbo kit. Hard water lines, prefabbed, cut to length with HEX center bolts for easier install on the turbo housing. Vibrant fittings and adapters. Replaces vibrant braided water lines. Learn More -
K&N High-Flow Air Filter - GR Corolla
Regular Price: $54.98
Special Price $51.97
K&N High-Flow Air Filter - GR Corolla Direct fitment in the GR Corolla OEM Air Box. FEATURES * High Air Flow with Excellent Filtration * Designed to Increase Horsepower and Acceleration * Washable and Reusable * Will NOT Void Vehicle Warranty * Lasts up to 50,000 miles before cleaning is required depending on driving conditions * K&N Million Mile Limited Warranty * Emissions Legal in all 50 US States. * Economical, a K&N Air Filter Will Last the Life of Your Automobile * Works with Original Equipment Manufacturer Vehicle Electronics * Easy High Performance Add-on * Environmentally Friendly Learn More -
Liquid Moly 0W-16 5L / K&N Filter / Drain Gasket
Regular Price: $67.18
Special Price $59.98
Liquid Moly 0W-16 5L / K&N Filter / Gasket Oil Change Bundle for the Corolla 2.0L (Engine M20A-FKS) Includes: - Liquid Moly 0W-16 5L - KN Gold Filter - OEM Toyota Drain Plug Gasket Notes: E210 2.0L Drain and refill with oil filter change: 4.9 liters 30 ft/lbs (Oil Drain Plug) Install a new washer on the drain bolt. Learn More -
Eibach Sportline Kit +19 Corolla Hatch/Sedan (-1.8 Drop)
Regular Price: $350.00
Special Price $329.78
Eibach Sportline Kit +19 Corolla Hatch/Sedan (-1.8 Drop) Eibach'sSportline lowering springs are the most popular springs they make—and there's a reason for that. These springs reduce fender gap to give your vehicle a lower, more aggressive stance. Plus, they help to lower the center of gravity to improve handling during acceleration, cornering, and braking. Best of all, you can lower your vehicle without having to change your shocks. Eibach gives you high performance handling and aggressive good looks. Extreme Performance Meets Extreme Style. Race-Car Like Handling. Lower Center of Gravity. Stop Quicker Corner Faster and get Better MPG! Million-Mile Warranty Learn More -
Project Kics 16+4 Locks Black R40 Iconix W/ Plastic Cap (Black) - 12X1.50
Regular Price: $291.98
Special Price $287.78
Project Kics 16+4 Locks Black R40 Iconix W/ Plastic Cap (Black) - 12X1.50 The Project Kics R40 Lug Nut is made of SCM435 Alloy for light weight and high strength. The M12x1.25 and M12x1.50 thread pitch R40 in Black Chrome or NeoChrome features two-piece construction with the floating seat design and allows you to properly torque your R40 Lug Nuts on your wheels without marring the finish. The R40 Non-Locking Lug Nuts come in packs of 20 in all standard 17mm hex lug nuts or with 16 standard 17mm lug nuts and 4 locking nuts with key. - Manufactured of high strength SCM435 Alloy - Open end racing design - Light weight lug reduces unsprung weight - Floating washer seat provides torque retention and eliminates wheel gouging - Available in Black chrome and special NeoChrome finish - Patented design - *Kits comes in either a lock version (16+4) or non-locking version which is 20pcs all lugs. NOTE: LUG NUTS ARE MADE WITH TAPERED BOTTOMS SPECIFICALLY FOR AFTERMARKET WHEELS. DO NOT USE THESE TUNER LUGS FOR YOUR FACTORY WHEELS. WE NO LONGER ACCEPT RETURNS ON LUG NUTS FROM CUSTOMERS WHO ATTEMPT TO USE THEM ON FACTORY WHEELS. THESE LUGS ALSO DO NOT FIT ON SPECIAL WHEELS THAT REQUIRE INVERTED LUGS. WE WILL ALSO NOT ACCEPT RETURNS FROM CUSTOMERS THAT TRY TO USE THEM FOR THESE TYPES OF WHEELS. Learn More -
Project Kics 12x1.50 R40 Lug Nuts - Neo Chrome (16+4 Locks)
Regular Price: $291.00
Special Price $278.97
Project Kics 12x1.50 R40 Lug Nuts - Neo Chrome (16+4 Locks) The Project Kics R40 Lug Nut is made of SCM435 Alloy for light weight and high strength. The M12x1.25 and M12x1.50 thread pitch R40 in Black Chrome or NeoChrome features two-piece construction with the floating seat design and allows you to properly torque your R40 Lug Nuts on your wheels without marring the finish. The R40 Non-Locking Lug Nuts come in packs of 20 in all standard 17mm hex lug nuts or with 16 standard 17mm lug nuts and 4 locking nuts with key. - Manufactured of high strength SCM435 Alloy - Open end racing design - Light weight lug reduces unsprung weight - Floating washer seat provides torque retention and eliminates wheel gouging - Available in Black chrome and special NeoChrome finish - Patented design - *Kits comes in either a lock version (16+4) or non-locking version which is 20pcs all lugs. NOTE: LUG NUTS ARE MADE WITH TAPERED BOTTOMS SPECIFICALLY FOR AFTERMARKET WHEELS. DO NOT USE THESE TUNER LUGS FOR YOUR FACTORY WHEELS. WE NO LONGER ACCEPT RETURNS ON LUG NUTS FROM CUSTOMERS WHO ATTEMPT TO USE THEM ON FACTORY WHEELS. THESE LUGS ALSO DO NOT FIT ON SPECIAL WHEELS THAT REQUIRE INVERTED LUGS. WE WILL ALSO NOT ACCEPT RETURNS FROM CUSTOMERS THAT TRY TO USE THEM FOR THESE TYPES OF WHEELS. Learn More -
Project Kics 12x1.50 R40 Lug Nuts - Black (16+4 Locks)
Regular Price: $245.98
Special Price $215.78
Project Kics 12x1.50 R40 Lug Nuts - Black (16+4 Locks) The Project Kics R40 Lug Nut is made of SCM435 Alloy for light weight and high strength. The M12x1.25 and M12x1.50 thread pitch R40 in Black Chrome or NeoChrome features two-piece construction with the floating seat design and allows you to properly torque your R40 Lug Nuts on your wheels without marring the finish. The R40 Non-Locking Lug Nuts come in packs of 20 in all standard 17mm hex lug nuts or with 16 standard 17mm lug nuts and 4 locking nuts with key. - Manufactured of high strength SCM435 Alloy - Open end racing design - Light weight lug reduces unsprung weight - Floating washer seat provides torque retention and eliminates wheel gouging - Available in Black chrome and special NeoChrome finish - Patented design - *Kits comes in either a lock version (16+4) or non-locking version which is 20pcs all lugs. NOTE: LUG NUTS ARE MADE WITH TAPERED BOTTOMS SPECIFICALLY FOR AFTERMARKET WHEELS. DO NOT USE THESE TUNER LUGS FOR YOUR FACTORY WHEELS. WE NO LONGER ACCEPT RETURNS ON LUG NUTS FROM CUSTOMERS WHO ATTEMPT TO USE THEM ON FACTORY WHEELS. THESE LUGS ALSO DO NOT FIT ON SPECIAL WHEELS THAT REQUIRE INVERTED LUGS. WE WILL ALSO NOT ACCEPT RETURNS FROM CUSTOMERS THAT TRY TO USE THEM FOR THESE TYPES OF WHEELS. Learn More -
Project Kics 12x1.50 R40 Lug Nuts - Neo Chrome (20 Pcs)
Regular Price: $258.00
Special Price $233.77
Project Kics 12x1.50 R40 Lug Nuts - Neo Chrome (20 Pcs) The Project Kics R40 Lug Nut is made of SCM435 Alloy for light weight and high strength. The M12x1.25 and M12x1.50 thread pitch R40 in Black Chrome or NeoChrome features two-piece construction with the floating seat design and allows you to properly torque your R40 Lug Nuts on your wheels without marring the finish. The R40 Non-Locking Lug Nuts come in packs of 20 in all standard 17mm hex lug nuts or with 16 standard 17mm lug nuts and 4 locking nuts with key. - Manufactured of high strength SCM435 Alloy - Open end racing design - Light weight lug reduces unsprung weight - Floating washer seat provides torque retention and eliminates wheel gouging - Available in Black chrome and special NeoChrome finish - Patented design - *Kits comes in either a lock version (16+4) or non-locking version which is 20pcs all lugs. NOTE: LUG NUTS ARE MADE WITH TAPERED BOTTOMS SPECIFICALLY FOR AFTERMARKET WHEELS. DO NOT USE THESE TUNER LUGS FOR YOUR FACTORY WHEELS. WE NO LONGER ACCEPT RETURNS ON LUG NUTS FROM CUSTOMERS WHO ATTEMPT TO USE THEM ON FACTORY WHEELS. THESE LUGS ALSO DO NOT FIT ON SPECIAL WHEELS THAT REQUIRE INVERTED LUGS. WE WILL ALSO NOT ACCEPT RETURNS FROM CUSTOMERS THAT TRY TO USE THEM FOR THESE TYPES OF WHEELS. Learn More -
B16 Garrett 60 Trim Turbo Kit (07-12) 450hp
Regular Price: $6,298.78
Special Price $4,698.00
B16 Garrett 60 Trim Turbo Kit (07-12) 450hp Fits: 07-12 Sentra 2.5L (SE-R and SpecV) Gains: Up to 450whp 2JR is the only B16 Turbo Kit that includes the 02 Sensor ports - before the turbo, in their respective bank - for perfect driveability and tuning. No other kit offers this option. The ECU must see Bank 1 and 2 separately. Kit Includes: Garrett 60 Trim Stage 3 Journal Bearing Turbo Turbosmart WG38 Gen V Ultragate 38 7psi Blue Turbosmart BOV Vee Port Pro Bosch 850cc Injectors Stainless Downpipe Vibrant Hardware Same Side Intercooler Turbosmart Boost Gauge Wastegate spring set to 7psi for 320whp out of the box. Higher rate springs can be spec'd for up to 450hp. Contact us after purchase. NOTES: You will need to move your battery to the trunk and lower the ECU (see photo). You will also need to remove your tow hook from the crash bar to fit the FMIC. Standard kit comes with an open dump for the WG. Options include powdercoated piping / closed dump / larger injectors. You may need to relocate/remove foglights. Kit will need to be tuned after install. Contact your local tuner or 2J Learn More -
E210 Brushed Stainless Header - In Stock
Regular Price: $699.98
Special Price $629.78
E210 Brushed Stainless Header - In Stock UEL Design / Stainless Steel with EGR Port. Incredible power gains, amazing sound! It comes complete ready to drop in, no modification required. Fits on the OEM midpipe or 2JR Midpipe. Now includes stainless steel header to manifold (engine) gasket Fits Sedan/Hatchback 2.0L Only Learn More