2JR Focus ST Cowl Induction Intake

Availability: In stock

Regular Price: $349.99

Special Price $239.99

Quick Overview

WE KNOW IT'S A LOT - BUT PLEASE READ BEFORE ORDERING!

The 2013-2014 Intakes are in stock and shipping today. The 2015+ are in production and will ship at the end of November.

Template for the cowl cutout - use only as a reference
https://1drv.ms/u/s!AjQkUN52fS1SkYsxogJlFVCW9jLMrw

Check out the full install of the 2J Racing cowl induction intake for the Focus St here: https://youtu.be/MtipNgHJUX0

Check out the complete unboxing of the NEW 2J Racing cowl induction intake for the Focus ST and RS here: https://youtu.be/zhqUlagPoRI

Check out the Comparison between the NEW 2J Racing cowl induction intake and my old depo intake here: https://youtu.be/GoTbfZnQ3EI


2JR introduces the world's first and only cowl induction intake for your Focus ST. Most intakes place the air filter behind the stock fans to pull heated air directly into the engine (after being heated again by the compression of the turbo). 2JR places the filter inside the cowl, where it only receives ambient cold air from beneath the windshield - in a very high pressure area (another benefit). NOTE - this intake IS LOUD. To us tho, it sounds amazing. Please refer to the "production photos" listed to the left of the final version of the intake.

You will lose your sound symposer - you do not need a block off plate (you can just remove the tube). The 2JR Cowl intake does include the provision for the EVAP hardline. Its completely plug and play - the OEM hardline clips in to our machined fitting - we have an extension hose that connects to the cowl intake. Same for the IAT sensor - instead of the silly grommet ours is a machined fitting the sensor rotates into - just like stock. So it'll never come lose or leak.

- Install time - 2 hours. A tune is not required.
- In testing we saw ambient or just a deg or two below ambient during cruising and slight increases under heavy load.
- To install you will need to cut the lower plastic housing under the cowl (very easy) and the upper cowl vent panel (we will provide a template for the vent panel) - you will also need to extend your IAT wires (2 of them) by 36" or purchase the optional JMS IAT Extension. All other hoses, clamps and K&N Air Filter are included in the kit.
- Made in the USA for perfect fitment and quality.


NOTE: The intake filter sits suspended in the cowl (not resting on the floor). The was done to prevent any water from being pulled in the intake that may build up on the cowl floor. We do recommend the optional KN filter sock to help keep the filter extra dry - as the piping turns down very close the the plastic upper cowl seal at the windshield. For added security you could trim the upper cowl to act as a bit of flashing to help offset any water intrusion. In testing, we didnt incur any issues during heavy rains - but you should always maintain the highest precaution against this occurring in your neck of the woods.

FINAL NOTE: JMS made for us the IAT extension harness. If you dont want to add 36" to your stock IAT harness (2 or 4 wires need to be extended) add this JMS harness in the options. Makes for a painless install. We also recommend the KN Dry filter Sock to help keep it dry.

2JR Focus ST Cowl Induction Intake

Double click on above image to view full picture

Zoom Out
Zoom In

More Views

  • Pre-Production pipe shown here
  • TB Strut Bar - with bracket created by customer Marius Solomon
  • TB Strut Bar - with bracket created by customer Marius Solomon
  • TB Strut Bar - with bracket created by customer Marius Solomon

* Required Fields

Regular Price: $349.99

Special Price $239.99

Details

2JR introduces the world's first and only cowl induction intake for your Focus ST. All other intakes place the air filter behind the stock fans to pull in heat directly into the engine (after being heated again by the compression of the turbo). 2JR places the filter inside the cowl, where it only receives cold air from beneath the windshield. NOTE - recommended for racing purposes as this intake IS LOUD. Extremely loud inside the car. You may use it on the street, but you will be listening to induction noise whenever you step on the gas. Install time - 2 hours. A tune is not required. To install you will need to cut the lower plastic housing, the upper cowl vent (we provide a template on the vent) AND extend your IAT wires. All other hoses, clamps and K&N filter are included in the kit. Made in the USA for perfect fitment and quality.

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.